Totalt: kr 0,00
Totalt: kr 0,00

1A USB Lithium TP4056 batterilader battery charging module with protection

(1 omtale)

kr 39,00 inkl. mva

Batterilader som også kan benyttes til voltage boost.

På lager og sendes omgående! (11)

Klikk her om du har funnet varen billigere et annet sted!

7000000058653 Produktnummer: 7000000058653 Kategori: Stikkord: , , , , ,

Beskrivelse

Board size: approx. 26 * 17mm
Input voltage: 5V
Charging cut-off voltage: 4.2V ± 1%
Maximum charge current: 1000mA
Battery over discharge protection voltage: 2.5V
Battery overcurrent protection current: 3A
Instructions:
1. Test current ammeter can only be connected in series at the 5V input of the charging board.
2. Charging current is best battery capacity of 0.37C, is 0.37 times the capacity, such as 1000mAH battery charge current 400 is enough. Too fast to charge the effect of fast, red finished the battery voltage out on the more.
3. The charging connection wire can not be too long. So that the connection resistance is large. Too thin words out of the battery voltage out of the more.
4. Good connection with the battery is good. Or rushed out of the battery voltage out of the more.
5. If the 5V input voltage is high, such as 5.2 or even 5.5, will cause the charging current less than 1000mA, which is normal. High voltage chip heat will automatically reduce the charge current, not to burn the chip. Chip in the work of about 60 degrees heat is normal. After all, the charging current is large.
6. Input reverse does not affect the chip, but the output (battery side) will burn back the chip.

SPECIFICATIONS:

Charge ControllerTP4056 / TC4056
Protection ICDW01A
Charge/Discharge Control MOSFETFS8205A
Charge MethodConstant-Current/Constant-Voltage (CC/CV)
Input Supply Voltage4.5~6.0 V
Constant Charge Current1 A
Configurable with Rprog resistor (R3, see diagrams and TP4056 / TC4056 datasheet)
Charge Complete (Float) Voltage4.2 V ±1.5%
Overcharge Protection
Overcharge Detection Voltage4.3 V ±50 mV
Overcharge Release Voltage4.1 V ±50 mV
Over-Discharge Protection
Over-Discharge Detection Voltage2.4 V ±100 mV
Over-Discharge Release Voltage3.0 V ±100 mV
Overcurrent Protection
Overcurrent Protection Threshold3 A
Overcurrent Cutout Delay10~20 ms
Short-Circuit Cutout Delay5~50 µs
Trickle Charge (Battery Reconditioning)
Trickle Charge Threshold Voltage2.9 V ±0.1 V
Trickle Charge Current130 mA ±10 mA
Dimensions
Length28 mm (~1.103″)
Diameter17 mm (~0.669″)
Weight1.6 g (0.057 oz)

Tilleggsinformasjon

USB port

Micro USB, Mini USB

7000000058653

1 omtale for 1A USB Lithium TP4056 batterilader battery charging module with protection

  1. Ola Owrenn (bekreftet eier)

    Godt utvalg og rask ekspedering.

Skriv en omtale

Din e-postadresse vil ikke bli publisert. Obligatoriske felt er merket med *

Du liker kanskje også…

×






Skriv inn din epostadresse så vi kan sende deg en mail når varen er på lager:
X
0
    0
    Handlekurv
    Tøm handlekurvTilbake til butikk
      Calculate Shipping
      Apply Coupon
      ×